can a center bolt on tensioner pulley be too tight?

We found this answers

How tight should the timing belt ... "I had to pull the tensioner pulley off of it's pivot point in order ... If you can angle the pulley so it is facing like a ... - Read more

... the crank shaft pulley bolt, As it can be troublesome ... pulley bolt not too tight so that you can remove ... or hex centre bolt if the tensioner is an ... - Read more

Discussion about this question


can a center bolt on tensioner pulley be too tight? resources

How to Change a Belt Tensioner | eHow UK

It can be attached by one bolt in the center or ... on the pulley sprockets. Tighten the tensioner by ... Tensioner on a 2000 Chrysler Grand Voyager.

How tight does the tensioner pulley bolt need to be ...

"Loosen the tensioner pulley center bolt, ... tensioner stays within the range, but too loose and you ... get the bolt tight enough, I can flip the ...

How to Remove a Tensioner Bolt | eHow

Removing the tensioner bolt is a fairly simple job that can be done ... the top of the tensioner and tighten the bolt with a ... Bolt From a Tensioner Pulley.

How to Remove the Bolt From a Tensioner Pulley | eHow

The tensioner pulley is on the ... tensioner, and for most vehicles, you can purchase and ... unit to loosen or tighten the belt. Removing the tensioner bolt ...

Nissan Repair / How to Replace AC Compressor Belt on 92 ...

nissan altima, tensioner pulley, center bolt: ... The compressor should have a tensioner pulley that you ... If the center bolt is really tight you can use one ...

| Repair Guides | Engine Mechanical Components | Timing ...

If the pulley has moved, the belt will be too tight. ... Fig. Adjusting the timing belt tensioner pulley-Mitsubishi ... Torque the tensioner pulley center bolt ...

SHOW MORE ....

Can you explain how to change the timing belt on my ...

Push the tensioner up against the tensioner pulley and tighten the ... pulley center bolt. NOTE: If the timing belt is ... too quickly, damage to the pushrod can ...

Audi A4 (B5). Timing Belt/Tensioner FAQ/Water Pump and ...

Timing Belt/Tensioner FAQ/Water ... screwdriver fits into so you can remove the 3 hex bolts that are ... tighten the center bolt attaching the pulley to ...

C5 Corvette Belt Install - How To Replace An LS1 Belt ...

... tensioner, and idler pulley on your 1997-2004 Chevrolet ... and idler pulley were all ordered from Corvette ... make sure this bolt is good and tight.

BMW 1985 – 325e Timing Belt and Water Pump Replacement

Tighten tensioner bolts. Re-assembly: ... Pulley. After getting the sheared bolt squared away, ... the center of the broken bolt an removed it with an

DIY Hyundai Elantra - Kia Spectra How To Timing Belt ...

DIY How To Timing Belt and Pulley ... the Pulley Bolt can be ... Push the Tensioner Pulley against the belt to remove slack and tighten the Tensioner Pulley Bolt.

Timing belt too tight? - Honda-Tech

Timing belt too tight? Honda Civic/Del Sol ... uuuummm yeah you can have an overtightened timing belt, ... loosen your belt tensioner bolt ...

Accessory Belt Tensioner, Upper And Lower, Automatic Belt ...

A broken Accessory Belt Tensioner can be a ... Most tensioner devices have a bolt head in the ... itself is a pulley that can be adjusted to tighten the belt's ...

Z32 Wiki - Timing Belt Service - Wikispaces

Timing Belt; Tensioner; Water Pump; ... Re-install the crank pulley bolt by hand so you can use the 27mm socket + a ... Tighten this bolt VERY SLOWLY. If you go too ...

Mitsubishi galant: I am putting a new timing belt on, I ...

... while tightening the center bolt. Tighten the center ... center of the tensioner pulley to the left and ... center bolt. Install Mitsubishi Special ...

AudiWorld Tech Articles

... JustDave did most of the replacement of the timing belt and tensioner. ... tighten the center bolt attaching the pulley ... can put the bolt through and tighten ...

| Repair Guides | Engine Mechanical Components | Accessory ...

Although it is generally easier on the component to have the belt too loose than too tight, ... Rotate belt tensioner ... on the tensioner idler pulley center bolt ...

How to Take off the Belt Tensioner on a 2002 Ford Windstar ...

How to Take off the Belt Tensioner on a 2002 Ford Windstar ... on the tensioner pulley bolt. ... tensioner in its place and tighten the bolts to 35 foot ...

How to Remove a Serpentine Belt Using Auto Tensioner: 13 Steps

... these systems used multiple belts on pulley systems with a number of ways to manually tighten ... tensioner pulley ... can cause the tensioner or where ...

97 6cyl TJ Serpentine Belt, Too Tight? - JeepForum.com

I've heard you can cause early wear failure on accessory pulleys if it's too tight, ... tensioner pulley bolt head is from the power steering pump pulley center bolt ...

Changing the Timing Belt - Kelly-Mulhern Performance

The mouting plate pulls out to reveal the center portion of the timing cover. ... Loosen the bolt holding the tensioner pulley. ... tighten the tensioner down, ...

How to Loosen a Serpentine Belt Tensioner - Life123

So, you need to know how to loosen a serpentine belt tensioner. There are three types of tensioners that may be encountered when replacing a serpentine belt.

How To Replace an Alternator - AA1Car.com

On applications where the position of the alternator can be adjusted to tighten ... pulley from the alternator ... tighten the bolts if the alternator must ...

Volvo Forum • Timing Belt Tensioner Pulley Bolt Stripped

Timing Belt Tensioner Pulley Bolt Stripped. ... the Torx bolt on the tensioner pulley. ... fall off and you can grip the outer edge of the bolt head with the ...

E30 Timing Belt Replacement - Chris's E30 page

Next, replace the timing belt tensioner pulley. ... (top dead center) ... (The lower tensioner pulley bolt can be hard to get a torque wrench on.

Replace cam belt (S1 K series manual tensioner)

Replace cam belt (S1 K series manual tensioner) These instructions describe how to change the cam belt on S1 cars with a Rover K series engine.

V6Z24 | How-To - Underdrive Pulley Install

Remove the center bolt from the pulley ... tighten the center bolt, to force the pulley ... Use a breaker bar to pull up on the tensioner pulley so you can ...

B6 A4 1.8T: Timing Belt and Water Pump DIY

Now move the pulley around so you can slide the lower tensioner in. tighten the bolts for the lower tensioner and take a ... tight the center nut on the pulley. ...

How to Remove the Belt Tensioner on a 1997 Buick LeSabre

How to Remove the Belt Tensioner on a 1997 Buick LeSabre ... A faulty tensioner can cause ... Install the tensioner pulley bolt and tighten it with the ...

Automatic Belt Tensioners - Honda CRX

... it may come off its pulleys. Too much tension ... on the tensioner pulley center bolt to ... bolt so the tensioner in a tight engine compartment can be ...

What Is a Tensioner Pulley? - wiseGEEK

A tensioner pulley is a device that can be used to ... by turning a bolt, ... until the belt is tight, at which point the pulley can be ...