How do you rub out a poly finish?

We found this answers

Rubbing Out a Shellac Finish for a Semi ... do you wait for the shellac to cure ... of sealer.I use a poly rub on sealer to seal the shellac. You need to seal ... - Read more

buffing out a guitar finish. ... Also be aware some finishes will not rub out to a shine. ... Whatever you do try and find out whats on there already. - Read more

Discussion about this question


How do you rub out a poly finish? resources

Rubbing out a water based poly finish | Fine Woodworking Knots

How you rub out a water-based finish depends on several things. What kind of finish is it? How was it applied? How many coats did you apply? And, most importantly ...

Rubbing out a polyurethane finish - Sawmill Creek

What is the best method to rub out a polyurethane finish? ... by rubbing out a poly finish. If you want a ... Do you realize that non poly varnishes don't ...

Rubbing out a polyurethane finish - DoItYourself.com ...

Rubbing out a poly finish can be done, but as you suspect, there's a hazard built in because of the difference in the finish. Lacquer is an evaporative finish.

Rubbing Out: The Final Step to a Great Finish | Articles ...

You can rub out all types of film ... The Final Step to a Great Finish. by Michael Dresdner. You can rub out all types of film ... Do this immediately and do not ...

Rubbing Out a Piano Finish - WOODWEB

Rubbing Out a Piano Finish The ... they do not rub out well at all! ... Too soft a surface just will not rub out to much of a shine, no matter how you do it.

Rubbing out a finish - by dpwalker @ LumberJocks.com ...

The important thing that Clint touched on is your choice of finish. Don’t try to rub out poly to a high gloss. It’s like trying to polish a tire.

SHOW MORE ....

Hand-Rubbed Lacquer Finish - DIY Woodworking

A properly completed lacquer finish is clear, ... rub the finish thoroughly. ... You can opt-out at any time.

Rub Deeper - About.com Barbecues & Grilling

Rubs flavor meat and add a whole new level ... So where do you start? Generally dry rubs start out with a few basic ... To finish off your rub try adding some ...

Rub out shellac with oil soap? - HomeOwnersHub.com

Can you rub out shellac using Murpheys oil soap as a lubricant? ... same finish in the end. I don't know about Murpheys, ... but will they come when you do call them?"

Rubbing Out A Finish - WoodWorkStuff

Rubbing out the finish. From the second you start ... difficult to rub out is that ; they do not ... block that you used for rubbing the pumice, if you do, ...

Buffing out a varnish finish - Search Results - North ...

Has anyone used an buffing machine and auto polishing compound to get the dust nibs out of a varnish finish? If so could you ... do not rub out to a high gloss. Poly ...

Rubbing Out Paint - Home | Inter.net

I am not one of those so I have to rely on having to rub out the pain tot get a nice finish. ... to add enough clear coats so than when you do rub out the paint ...

How do i buff a linseed finish to a shine? - Page 2

... only boiled and the more you rub it the better ... It takes many hours to produce the London finish so famous for linseed oil ... as I do not like poly.

HowStuffWorks "How to Restore Wooden Furniture Finish ...

... shellac, lacquer, or varnish. Before you do any work on the finish, ... If alcohol doesn't affect the finish, rub a ... "How to Restore Wooden Furniture Finish ...

Woodworking Q&A with Bruce Johnson - Wood Finishing | Minwax

A. The white ring is moisture that has been absorbed by the finish. When you do get white rings appearing, this is a sign that the finish is wearing out and losing ...

How to Finish Maple: 5 Steps - wikiHow

Be careful that you do not sand the corners and remove ... making note of how it turns out in each step of ... There are other ways to finish maple you can ...

High Gloss Finish-Any Way To Knock It Out?

... compared to poly and oil rubs. ... But if you really want a matte finish just do the ... Your best bet is pumice stone Rub it out with fine pumice and either ...

Spraying and rubbing out semi-gloss finish

The problem is that if you rub out one part of a job you have ... left is small it may flow out as the finish dries. You can also ... cars out and do a ...

Furniture Repair and Assembly: Finish Fisheye, dust bumps ...

dust bumps, finish rub out: There is a major difference in appearance between a rubbed out finish and one that is off the gun (spray gun) or brushed. Any type of ...

Wood Finishing - 20m

This article is an attempt to provide you with a few easy finishing procedures to follow and ... You do not want this bleeding ... To rub out the finish, ...

DIYonline.com - home improvement & remodeling made easy ...

... smooth this out. Either kind of polyurethane will ... poly, you can rub down the finish with a ... way, do not rub too hard. Types of Polyurethane:

Homeshop Finishes That Work! - 20m

Rub out the finish with a white 3M ... you have a spray booth. Why the booth? Poly overspray does ... If you never do it at all the only harm ...

Rubbing Out Poly - Woodwork Forums

I'm (still) trying to figure out how to rub out a polyurethane finish ... if you do not know as I have just ... Don't keep rubbing out the poly as you'll end up ...

Rubbing Out A Finish Part 2 - World News

Rubbing Out a Finish ... Part 2, Rubbing Out a Finish - Part 1, 213 - Rubbing Out a High Gloss Finish, Fast Finish Rub-Out, ... Brought to you by http ...

Rubbing out finish - WOOD Community

... two days of drying time is way too little if you plan to rub it out. First, poly ... This final rubbing may take a while with polyurethane ... Do all finish ...

Can I rub out Minwax Polyshades? [Archive] - Woodworking ...

I'm not sure if I can rub out this type of finish, ... I'm New to Woodworking and ... > Can I rub out Minwax Polyshades? PDA. ... How do you put the finish on? A ...

Rubbing out a WB poly Finish to Satin - by BLarge ...

Anybody use 4 aught steel wool to rub out a water based poly finish ... when you finish ... Any posts on LJ are posted by individuals acting in their own right and do ...

Rubbing Out a Finish [Archive] - Woodworking.com Forum

Jim, In my experience, 3 coats for a wipe on is too thin, I normally go with 6. I've also never had to rub out a wiped on poly... Generally, a finish should be rubbed ...

Michael Dresdner » Blog Archive » Rubbing out a Finish

... you can rub them out provided the finish is ... I tried rubbing out a finished table top ... If I attempt to rub out this last coat, would I do the same ...

Wood Finishing Tips: Hand Rubbed Poly Finish - YouTube

... by hand I always go for the hand rubbed Poly. ... but if I have to do it by hand I always go for the hand rubbed ... Finish Rub-Out by ...

How long to cure poly before rubbing out - Woodworking ...

Next thing why do you want to rub out a poly finish to begin with? If you want satin, ... Your wanting to know how long till you can rub out a poly finish?